跳至主要内容

XTOOL X100 Pad2 key reprogram a 2004 Land Rover Discovery 3

 

Discovery 3 is supported by X100 PAD2/ X100 PAD2 Pro in key programming. Check the Land Rover IMMO function list as below.

Landrover Immobiliser Function List: 26.63
Automaker Model/Protocol System Function
LANDROVER Range rover(Sport) 2005-2009 Immobiliser 1.Program keys
LANDROVER Range rover(Sport) 2010-2015 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Range rover 2006-2009 Immobiliser 1.Program keys
LANDROVER Range rover 2010-2015 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Range rover 2010-2013 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Range rover 2014-2015 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Range rover (Evoque)-2013 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Range rover (Evoque) 2014-2015 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Discovery 3 Immobiliser 1.Program keys
LANDROVER Discovery 4 -2013 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Discovery 4 2014-2015 Smart key system 1.Add smart key
2.All smart key lost
LANDROVER Freelander Immobiliser 1.Program remotes
LANDROVER Freelander 2(-2012) Immobiliser 1.Smart key
LANDROVER Freelander 2(2012-) Smart key system 1.Add smart key

2.All smart key lost

It’s not difficult to do key programming, just do it as follows.

Connect X100 Pad2 key programmer to the vehicle via the main cable properly

Turn on the XTOOL tablet to operate

Go to “Immobilization”-> “LANDROVER”

Agree with the disclaimer

Select “Discovery”-> “Discovery 3”-> “Program keys”

Note: you need at least one programmed key.

Then follow the on-screen instructions to operate step by step.

Insert the working key into the ignition and no need to turn on

When it has been programmed successfully, remove it and insert the new key, do not switch ignition on

After the process is completed, test two keys

FYI…

Some customers have successfully tested on other Land Rover car models, also share here with you.

* LR Sport 2009 add Chinese remote key OK
* Ranger T6 2015 AKL, lishi for door lock and X100 pad2 for programming. 2mn done.
* land rover freelander 2 2012 add 1 key
* landrover freelander 2006 add remote it’s ok
* Ranger 2017 Hitag Pro: add key OK
* range rover sport 2012 add key ok
* Disco 4, add smart OK (Hitage Pro)

评论

发表评论

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

  SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...
发表评论
阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

  When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of  ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click  “yes” when below  page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...
发表评论
阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of  BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...
发表评论
阅读全文