跳至主要内容

Ford VCM II firmware update or downgrade

It’s confirmed that Ford VCM II Firmware Update And Downgrade is possible, Operation steps guide here (This guide applies to all vcmii tools)

Procedure:

Remove the rubber case shown below.
Ford-VCM-II-firmware-update-or-downgrade-1 Ford-VCM-II-firmware-update-or-downgrade-2

Connect the USB cable to the VCM2 device and hold the (ReSet) button shown as below.

Ford-VCM-II-firmware-update-or-downgrade-3

Connect the other end of the USB to a computer with IDS V86 installed, and then release the ReSet button until you hear a beep sound.

Ford-VCM-II-firmware-update-or-downgrade-4

Run Bosch\VCI Software(Ford-VCM-II)\VCI Manger(Ford-VCM-II).

Ford-VCM-II-firmware-update-or-downgrade-4

When you see the following image, it means you enter the recovery mode.

Ford-VCM-II-firmware-update-or-downgrade-5

After clicking on the “Recover” button, the program will switch to the VCMII Update interface.

Ford-VCM-II-firmware-update-or-downgrade-6

Click on “Start Update” to start the firmware update, and the following image will appear “Do not unplug the VCM II from the PC or remove power from the VCM II during the update process.”

Ford-VCM-II-firmware-update-or-downgrade-7

After clicking on “OK”, the following image will appear to start writing the new version of firmware.

Ford-VCM-II-firmware-update-or-downgrade-8

When the upgrade completed, the following prompt interface will appear, and the VCM II will automatically restart,wait until you hear the “beep”. Now exit VCM II Manager.

Ford-VCM-II-firmware-update-or-downgrade-9

Run the IDS. When the icon shown in the figure below appears, the VCM update is complete and it can be used normally.

Ford-VCM-II-firmware-update-or-downgrade-10

Enjoy!

https://fordtroublerepair.blogspot.com/2021/05/ford-vcm-ii-firmware-update-or-downgrade.html

标签：

评论

发表评论

此博客中的热门博文

Allscanner VXDIAG released the new Benz Xentry software 2021.12

  Benz software include two versions of PASSTHRU and PDU, including DAS, Xentry software . Version of PDU support new car models of 222, 213, 205 etc,other car models need to usepassthru version to diagnose. Not support old models of 210, 203, 220 with K-Line communication. It support connections of WIFI, LAN and USB. Allscanner VXDIAG released the new Benz Xentry software 2021.12 VXDIAG Benz Software: 2021.12 Xentry 30.8.2.1_v2 EPC/WIS 11/2018 StarFinder 2016-2020 SDmedia 2014 DTS Monaco 8.13.029 Win10 x 64bit system Affected devices:  Vxdiag Benz C6 , VCX SE Benz , VCX Plus Benz DoIP, VXDIAG Full etc Requirements: Requires V1.8.6 and later vx manager and new C6 driver (check update vx manager and c6 driver) Before it only recognized as passthru now with the new vx manager drivers all c6, passthru and DoIP works in DTS. 12/2021 Xentry Images Display Format: HDD or SSD
发表评论
阅读全文

CAT ET vs Cummins INLINE7 vs Nexiq USB-LINK 2 vs John Deere EDL v3 Reviews

1. Review by Alcoholahmed: Cat and perkins industrials ,gensets or even construction: Software:  Cat ET &  Perkins EST ( both are already here) And , you may uses cat communication adapter or perkins adapter for any of them. And NEXIQ only for the on-highway protocols J1578 or J1587 Volvo/Mack/Renault : Adapter : volvo VOCOM Software: volvo PTT can be used for most of newer on-highways trucks.( each model has some special cables) While ,marine/gensets/industrial you may use Volvo Vodia with a special connector to the VOCOM. Volvo Construction equipt.: uses another cables to the VOCOM and uses also PTT software with sometimes the MATRIS John Deere: uses the JD service advisor as software and EDL as an adapter. Hitachi :uses the MaintenancePro. Dr. As software Note: you may use your cummins Inline adapter for cat, perkins ,and reading JD error only. Hope that helps you 2. Review by illy : I’m also in search for universal adapter for off-highway use but I’m ...
发表评论
阅读全文

LAUNCH X431 V+ REVIEW

  Launch X431 V+  is full system auto diagnostic scan tool which is the update version of  X431 V Pro. It support  all systems diagnostics, ecu coding, key programming,resetting services,active test (Bi-directional control) and more. Is it worth to buy one? Let’s check the reviews of Launch X431 V+ by the users. Mickie: I have Snap On, Matco, and other scanners, and when I was recommended to the Launch X431 V+ for doing module programming, I was at first hesitant. But as all of my other scanners couldn’t program a wireless module and keys, so I ordered this scanner. What a machine! The launch X431 V+ handled the programming in a flash. Easy to use, and understand. I am looking forward to using this as my go-to scanner. Tolay: Really useful, easy to use I need this scanner for my shop, and definitely is a great tool, it has a lot of features, I think I got the best value for my money, I was between buying this or a way more expensive ...
发表评论
阅读全文