跳至主要内容

Autel MK808 Calibrate EPB for Porsche Cayenne 92A 2011-2017

 

How to use Autel MaxiCOM MK808 to do electronic parking brake(EPB) calibration for a Porsche Cayenne 92A 2011-2017? It is really simple and easy process, following I’ll show you.

Plug Autel MK808 connector into OBD2 port, press

Service >> EPB >> Porsche >> Manual selection >> 92A – Cayenne (2011-2017) >> Hot functions >> Electric parking brake

Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-1
Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-2
Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-3

Now we have a message “electric parking brake in service mode” on dashboard here.

We can go to “Grinding-in”, “Calibration” or “Check basic setting of parking brake” separately, but I’ll select “Replace brake pads(operation guide)” to show the whole process in order.

Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-4

Just follow the instructions to press command.

It will bring you to complete all operations:

Replace brake pads(operating guide) >> OK >> OK >> OK >> OK >> Continue >> Exit >> OK >> No >> Continue >> Start >> Continue >> Continue >> Continue >> Start

Calibration running, please wait…

Calibration completed, press “Continue” to finish.

All done!

Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-5
Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-6
Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-7
Autel-MK808-Calibrate-EPB-for-Porsche-Cayenne-92A-2011-2017-8

This is the guide on doing Porsche Cayenne 92A electronic parking brake with Autel Scanner MK808 Scan Tool. It makes EPB calibration much easier. Simply follow the instructions step by step, all can be done!

标签：

评论

发表评论

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

  SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...
发表评论
阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

  When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of  ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click  “yes” when below  page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...
发表评论
阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of  BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...
发表评论
阅读全文