How to Reset OBDSTAR X300 DP Plus to Solve Register Failure Problem

Here share the method to solve OBDSTAR X300 DP PLUS register failure problem by resetting the device.

Customer problem:
When I turned on my x300 dp plus, and tapped teamviewer to register, the registration interface appeared, but quickly jumped back to the user login interface. I tried it many times, it always showed the same problem.
x300dp plus log in

Obd2tool.com engineer replied:
Please try to reset the X300 DP PLUS to solve this problem.

Check the step-by-step guide below.

Step 1: Contact our customer service to get the boot package
Step 2: Copy the Android software with a formatted TF card

Note: Don’t put them in one file
Step 3: Turn on X300 DP Plus, insert the TF card into the slot of the DP Plus
Then long press “Power” button to turn until “update successful” appears.

Step 4: Turn off DP Plus, take out TF card
Then turn it on again
It will take 2-3 minutes during the process

Please kindly notice:
The software is the original software of OBDSTAR X300 DP Plus, which is necessary to register and update.

Guide to register X300 DP Plus:
1.Turn on OBDSTAR X300 DP Plus

Connect the power and charge it
2.Select “Setting”-> “User information”

Input the SN, user name, password, and email info (the register password appears automatically)

3.When register successfully, you can log in with the available user name and password.

Guide to update X300 DP Plus:
Tap “One Key Upgrade” to enter one key upgrade page

Click “Bulk update” to download all software

Note: Ensure internet connection is normal when updating.

http://chinaobdtool.net/2021/05/11/how-to-reset-obdstar-x300-dp-plus-to-solve-register-failure-problem/

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...

阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle, can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click “yes” when below page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...

阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...

阅读全文

OBD2 DIAGNOSTIC TOOL

搜索此博客