跳至主要内容

Launch X431 Rest Service Light for Mercedes Benz Maybach

 

This instruction show you how to reset service light for Mercedes Benz Maybach by Launch X431 device.If you want to more info about Benz repair cases,please check here:Mercedes Benz Repair.

What You Need?

Launch X431V+ Pro3

Conditions:

Switch on the ignition before implementation. Do not start the engine.
Switch off the ignition after implementation. Wait for 10s. Then switch it on.

Operation Procedure:

1.Switch ignition ON. Do not start the engine.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-1

2.Select the service light reset software version V10.30 or above.

3.Select “Mercedes-Benz” Menu.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-2

4.Select “Passenger Car”.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-3

5.Select “Software Reset”.

6.Select “Auto Scan” or “Manual Selection”.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-5

7.Select “Maybach”.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-6

8.It prompts to switch on the ignition. After this, it prompts “Communicating, please wait…” In about 1s,it displays “Confirm total service”.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-7

9.Select “Confirm total service”, it shows oil type (level).

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-8 Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-9

10.Select any type (level), it will display “Oil reset completed”. Click OK to complete.

Launch-X431-Rest-Service-Light-for-Mercedes-Benz-Maybach-8

More test report about Launch X431 please check:Launch X431 Test report

评论

发表评论

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

  SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...
发表评论
阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

  When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of  ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click  “yes” when below  page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...
发表评论
阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of  BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...
发表评论
阅读全文