跳至主要内容

How to Set Launch X431 V Ford Steering Angle Sensor Reset+ Clutch Leaning


Launch X431 V 8 inch How to reset steering angle sensor for Ford Mondeo? And how to do Clutch Adaptive Learning for Ford Focus? Following us, you’ll find the detail in this blog:
Part 1. Launch X431 V reset Ford steering angle sensor steps
Open Launch X431 V Ford software.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-1
Go to “Automatically Search” and it will show Ford Mondeo vehicle information as below:
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-2
Select Fuel Type, in this case the fuel type is gasoline.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-3
Click “System Selection” and select “ABS/TCS (Anti-Lock Brake/ Traction Control Module)”.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-4
Go to “Special Function”.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-5
Kindly Notice: Launch X431 V support many Ford useful garage special functions.
Choose “Configure The Steering Angle Sensor” function.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-6
Then follow Ford steering angle sensor calibration instruction:
*   Make sure car is stop not running on flat ground.
*   Make sure you set the steering wheel to straight ahead position.
*   You will need to rotate the steering wheel.
Click OK and turn on ignition (switch to position 2).
Then rotate the steering wheel about 10 degree to left and right.
Wait 3 or 4 seconds and Launch X431 V successfully reset steering angle sensor for Ford Mondeo!
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-7
Part 2. Launch X431 V Ford Clutch Relearn steps
Same procedure as the above until you go to “System Selection”.
Select “TCM (Transmission Control Module)” then “Special Function”.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-8
Choose “TCM Adaptive Learning”.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-9
You will see a pop-up TCM Adaptive Learning message. Click Yes to continue.
Turn on car ignition then choose “Clutch”.
How-to-Set-Launch-X431-V-Ford-Steering-Angle-Sensor-Reset+-Clutch-Leaning-10
Click Yes to continue.
Make sure the transmission gear selector is at PARK position.
Press and hold the brake pedal.
Wait about 15 seconds then Launch X431 V 8inch tablet complete Ford Focus Clutch Learning!
标签：

评论

发表评论

此博客中的热门博文

Autel MaxiSys Elite and Mercedes SCN Coding

I purchased the  Autel Maxisys Elite almost a year ago. I decided to buy it from an Autel representative based on his customer service skills and YouTube videos. I am based in the USA and the Autel rep is outside the USA. I paid a bit more for the tool because the direct human to human customer service is something I value a lot and it is something nearly extinct nowadays. Total price was $3600 USD and it was equipped with an additional cable for BMW programming and the nifty camera too. The Autel marketing practices do very little to bring clarity to the details of what the tool can and can not do. When it comes to programming various modules found in our vehicles, the details are lacking. It can program BMW and Mercedes Benz from the tablet, but it can not program GM modules because the software to program GM runs on Windows, not Android. However, you can use the Autel J-Box for your VCI and connect it to a Windows based PC using a USB cable and log on to the GM w...
发表评论
阅读全文

CAT ET vs Cummins INLINE7 vs Nexiq USB-LINK 2 vs John Deere EDL v3 Reviews

1. Review by Alcoholahmed: Cat and perkins industrials ,gensets or even construction: Software:  Cat ET &  Perkins EST ( both are already here) And , you may uses cat communication adapter or perkins adapter for any of them. And NEXIQ only for the on-highway protocols J1578 or J1587 Volvo/Mack/Renault : Adapter : volvo VOCOM Software: volvo PTT can be used for most of newer on-highways trucks.( each model has some special cables) While ,marine/gensets/industrial you may use Volvo Vodia with a special connector to the VOCOM. Volvo Construction equipt.: uses another cables to the VOCOM and uses also PTT software with sometimes the MATRIS John Deere: uses the JD service advisor as software and EDL as an adapter. Hitachi :uses the MaintenancePro. Dr. As software Note: you may use your cummins Inline adapter for cat, perkins ,and reading JD error only. Hope that helps you 2. Review by illy : I’m also in search for universal adapter for off-highway use but I’m ...
发表评论
阅读全文

LAUNCH X431 V+ REVIEW

  Launch X431 V+  is full system auto diagnostic scan tool which is the update version of  X431 V Pro. It support  all systems diagnostics, ecu coding, key programming,resetting services,active test (Bi-directional control) and more. Is it worth to buy one? Let’s check the reviews of Launch X431 V+ by the users. Mickie: I have Snap On, Matco, and other scanners, and when I was recommended to the Launch X431 V+ for doing module programming, I was at first hesitant. But as all of my other scanners couldn’t program a wireless module and keys, so I ordered this scanner. What a machine! The launch X431 V+ handled the programming in a flash. Easy to use, and understand. I am looking forward to using this as my go-to scanner. Tolay: Really useful, easy to use I need this scanner for my shop, and definitely is a great tool, it has a lot of features, I think I got the best value for my money, I was between buying this or a way more expensive ...
发表评论
阅读全文