跳至主要内容

Autel MaxiIM608 Read PIN Code for Dodge Smart Key

This test report feedback from our customer real test project,he use this new product Autel MaxiIM608 to read PIN code for Dodge smart key.And here is another test report: Autel IM608 All Keys Lost Programming for Range Rover Evoque 2013
Autel IM608 Related Contents：
Autel MaxiIM IM608 reviews on add key & all keys lost
Autel MaxiIM IM608 VS MaxiIM IM508 VS Auro OtoSys IM600 VS IM100
Autel IM608: Amazon? Ebay? obd2tool?
Operation Procedures:
Connect Autel IM608 to vehicle,then enter menu to select “Dodge”
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-1
Select “Smart Mode”
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-2
Turn the ignition on
If it is old pre 2006 model,please give priority selection to “Manual Selection” or “System Selection”!
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-3
Establishing vehicle communication
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-4
Select “knob-style smart card”
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-5
Switch the ignition off and then on again,make sure the engine off.
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-6
Establishing vehicle communication…
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-7
Switch the ignition off and then on again,make sure the engine off.
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-8
Establishing vehicle communication…
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-9
Then you will get the PIN code:8095
Autel-MaxiIM608-Read-PIN-Code-for-Dodge-Smart-Key-10


标签：

评论

发表评论

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

  SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...
发表评论
阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

  When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of  ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click  “yes” when below  page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...
发表评论
阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of  BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...
发表评论
阅读全文