Allscanner VXDIAG released the new Benz Xentry software 2021.12

Benz software include two versions of PASSTHRU and PDU, including DAS, Xentry software. Version of PDU support new car models of 222, 213, 205 etc,other car models need to usepassthru version to diagnose. Not support old models of 210, 203, 220 with K-Line communication. It support connections of WIFI, LAN and USB.

Allscanner VXDIAG released the new Benz Xentry software 2021.12

VXDIAG Benz Software: 2021.12
Xentry 30.8.2.1_v2
EPC/WIS 11/2018
StarFinder 2016-2020
SDmedia 2014
DTS Monaco 8.13.029

Win10 x 64bit system
Affected devices: Vxdiag Benz C6, VCX SE Benz, VCX Plus Benz DoIP, VXDIAG Full etc

Requirements:
Requires V1.8.6 and later vx manager and new C6 driver (check update vx manager and c6 driver)
Before it only recognized as passthru now with the new vx manager drivers all c6, passthru and DoIP works in DTS.

12/2021 Xentry Images Display
Format: HDD or SSD

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...

阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle, can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click “yes” when below page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...

阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...

阅读全文

OBD2 DIAGNOSTIC TOOL

搜索此博客