跳至主要内容

ICOM NEXT for BMW ISTA-D ISTA-P Software Download and Installation Guide

ICOM Next is professional diagnostic tool for all BMW E/F/G series cars, MINI, Rolls-Royce BMW-Model.  And it supports programming offline directly.  BMW ICOM software works with ICOM NEXT well, also ICOM A2.
Obd2tool.com here provide BMW Win7 ISTA-D/P software download and installation guide.
1. BMW ICOM Software Overview:
Software Version: V2020.03
BMW Diagnosis ISTA-D: 4.21.31
BMW Programming ISTA-P: 3.67.0.000
Operation System: Win7 32bit i5 4G RAM or above
2. ICOM Next A+B+C Diagnosis Software V2020.03 List:
BMW ICOM NEXT is latest generation after service tool for BMW.
These brief instructions describe the basic functions of the AIR application (Aftersales Information Research) in Service.
For the Diagnostic, it use IPSI (Rheingold) and also ISPI Next for Coding Programming functions.
ISTA/D – Integrated Service Technical Application Diagnostic.
ISTA/D is used to diagnose BMW all series and models from all systems.
ISTA/P – Integrated Service Technical Application/Programming.
ISTA/P is used to process all coded, programmed and enable-dependent control modules in B-MW Group vehicles.
Rheingold – Diagnostic and repair guide, including Diagrams and disassembly Figure.
KSD – B-MW KSD (Kaufm?nnische Service Daten.
i.e. Commercial Service Data) is a collection of invaluable data for determining labor hours, inspection sheets and general service methods.   There’s also information about wheels and rims for the various models.
EasyConnect – Used to Configure the Environment Parameter of Engineer Software for E series.  It can activate or release ICOM Port.
IToolRadar – Used to recognize ICOM, activate or release ICOM Port.
ETK – Accessories Catalog.
EDIABAS Tool32 – Engineer Software for E series, able to run directly.
INPA – Engineer Software for E series, for diagnosis.
NCS Expert Tool – Engineer Software for E series, for coding.
WinKFP – Engineer Software for E series, for programming.
E-sys – Engineer Software for F series.   (Available for programming and coding).
BMW Standard tool
Coding Database
Coding Tool
3. Software Free Download
Rheingold 4.12.12 Standalone / SDP 4.12.12 / ISTA-P 3.65.2.0   (SQLiteDBs EN,DE,RU,OTHER).
https://mega.nz/#!BaBkBawb!_buiiV3KAJ70_ds8mTEL_PBdsRKv3HiKoImaGo4hnQ0
Of course, you can find many other download links in some BMW forums as below.
https://www.bimmerfest.com/
http://www.bimmerpost.com/
http://www.bimmerforums.com/
https://www.BMWcca.org/
http://www.bimmerboard.com/
…
4. BMW ICOM software win7 installation guide
Usually we main install software with win7 32 bit system, and all test ok!
ICOM-NEXT-for-BMW-ISTA-D-ISTA-P-Software-Download-and-Installation-Guide-1
ICOM-NEXT-for-BMW-ISTA-D-ISTA-P-Software-Download-and-Installation-Guide-2
ICOM-NEXT-for-BMW-ISTA-D-ISTA-P-Software-Download-and-Installation-Guide-3
Step 1: ISTA-D Diagnosis software
Open software
Then double click RHEINGOLD icon to change Full Screen.
Go to Operations, then Read Out Vehicle Data, press Complete identification.
Then follow ISTA prompt to connect the ICOM emulator with vehicle.
When it shows ICOM, then you can click lower right corner Connect to start diagnosis.
(If the Status shows firmware, you see update ICOM firmware first, see instruction in Part 5).
Step 2: ISTA-P Programming software
Open ISTA-P software
Then click “Reset Settings” tab then close.
Open it again
Then select ISTA-P language and then Resolution.
Check the resolution on desktop.   It is the same as ISTA-P resolution you just chose.
Select vehicle type, BMW, MINI, BMW Motorcycle or Rolls Royce.
Then it will select ISTA-P server automatically.
Step 3: ETK
Open ETK software
Click “Extras” tab>> “Settings” to change language and other settings.
KSD
Then click “Settings” to change language and others.
Step 4: Engineer Tools
Engineering & programming software INPA, NCS-Expert, WInKFP etc.
Before using the engineer tools, must set/configure ICOM settings.
1) Open Engineer Tools, Itool Radar, select first line option.   Then click “Reserve” button on the right.
ICOM Device status will be changed to Reserved.
2) Open EasyConnect, do following settings.
The IP address must be set to correct 169.254.92.38.   Then click “CHECK” button.
Configuration is done.   And then  you can start using engineering software (INPA, WinKFP, etc.)
标签：

评论

发表评论

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

  SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...
发表评论
阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

  When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle,  can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the  latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of  ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click  “yes” when below  page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...
发表评论
阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of  BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...
发表评论
阅读全文