Chevrolet Trailblazer Duramax 2013 key program by VVDI Key tool and OBDSTAR DP plus

Chevrolet Trailblazer Duramax 2013 generate remote with VVDI Key Tool, program remote, read pincode with obdstar dp plus.

Part 1: generate remote with VVDI Key tool

Generate remote -> Remote program -> Remote key

America ->Chevrolet -> Trailblazer

Use XN remote (chip ID 46 7937E)

Put battery and press [Gen].

Burn succeed.

Install remote module into remote shell.

Part 2: Program Chevrolet Trailblazer Duramax 2013 key with OBDSTAR key master DP plus

1. Read Pin code
Turn on ignition with programmed key.

Read pincode.

There is Pincode in Service Booklet: 9465

If no service booklet, then you can find by OBDII.

Tap “Enter” – GM 31.15 -> Read security Code.

By OBDII -> BCM system -> Auto

Please ensure the internet connection is available.

Read Pincode — Logging…

Pincode: 9465

Program Chip
Back to tap: GM 31.15 -> Immobilizer-> Select from type -> Type3

Check key data: 2 keys.

Clear DTC.

All keys lost -> fill pin code:9465

Switch off for 5 seconds, then switch on.

System configuration, please wait for 10 minutes.

After 10 minutes.

Switch off and pull the key out.

Open and close driver door.

Switch on.

Whether to program next key? [Yes].

Switch off and pull the key out.

Insert new key and switch on.

Switch off and pull the key out.

Open then close driver door.

Switch on.

Whether to program next key? [NO] only 2 keys.

Switch off and pull the key out.

Open then close driver door.

Switch on

Switch off

Switch on

Program successfully.

Security light go off.

Start engine ok.

Test remote ok.

Done.

Thanks for reading.

此博客中的热门博文

How to Replace and Reprogram Chrysler FCM with DRB III

SUBJECT: Replacing or reprogramming the Front Control Module (FCM) OVERVIEW: Erroneous Actuation of Horns, Headlamps, and Parking Lamps while vehicle is parked MODELS: 2001 – 2004 (RG) Chrysler Voyager (International Markets) 2001 – 2004 (RS) Town & Country/Caravan/Voyager SYMPTOM/CONDITION: While the vehicle is parked the customer may experience the horn sounding on and off, flashing the headlamps and the parking lamps as if the security alarm was actuated. The technician may find the vehicle is not equipped with Security Alarm system (sales code LSA). DIAGNOSIS: 1. Using a Scan Tool (DRBIII®) with the appropriate Diagnostic Procedures Manual, verify all engine systems are functioning as designed. If DTCs are present record them on the repair order and repair as necessary before proceeding further with this bulletin. 2. Determine the “Hardware Part #” of the FCM. Using the DRB III select: 3. DRBIII Standalone 4. 1998 – 2005 Diagnostics 5. All 6. Body In...

阅读全文

How to update BMW ICOM A2 or ICOM NEXT Firmware

When using the latest ISTA D software to do BMW diagnosis, icom hareware can be detected, but the device doesn’t communicate with the vehicle, can’t enter modules reading page, like below picture: What’s the solution? The firmware doesn’t match with the latest ISTA sofware, firmware need to be updated. ICOM firmware update steps: 1. Need the latest updated file for ICOM firmware: 2.Charge ICOM hardware, connect the vehicle, use ISTA engineering sofware IToolRadar to detect the IP address of ICOM hardware, see below picture, the IP address can be found as 169.254.92.38 3. Open Internet Explorer Input the IP address which is deteced above to the address bar: like http://169.254.92.38:60080 username: root password: NZY11502 4. Click “update firmware” after login 5. Follow below steps: 6. Need to wait seconds, and click “yes” when below page show up: 7. During ICOM firmware update, four light on ICOM are all read, need to wait...

阅读全文

How to update the firmware of ICOM NEXT A

Upgraded the new version of BMW Diagnostic Software ISTA. When connected to the vehicle, click to start the vehicle to detect ICOM, but the State is Firmware. At this time, you need to upgrade the firmware of BMW ICOM Next ； ICOM NEXT A firmware upgrade steps 1. First, you need the firmware file of the new version of ICOM NEXT, the ICOM NEXT firmware file has a name with ICOM NEXT XXX, The two files xxx root xxx and xxx app xxx need to be upgraded. (Firmware version is different, the file name is different, but all versions of the firmware have the file name of ICOM_Nextxx) 2.ICOM NEXT A is connected to the car, usually the OBD interface of the car (the same method as the car diagnosis), open the diagnostic software ISTA, or use the software ITool Radar, you can detect the IP address of ICOM NEXT (IP address is automatically obtained), The IP address detected by the ISTA software is 169.254.192.155; 3.Open the IE browser, enter the IP address and port number of...

阅读全文

OBD2 DIAGNOSTIC TOOL

搜索此博客