OBD2 DIAGNOSTIC TOOL

  This instruction show you how to reset service light for Mercedes Benz Maybach by Launch X431 device .If you want to more info about Benz repair cases,please check here:Mercedes Benz Repair. What You Need? Launch X431V+ Pro3 Conditions: Switch on the ignition before implementation. Do not start the engine. Switch off the ignition after implementation. Wait for 10s. Then switch it on. Operation Procedure: 1.Switch ignition ON. Do not start the engine. 2.Select the service light reset software version V10.30 or above. 3.Select “Mercedes-Benz” Menu. 4.Select “Passenger Car”. 5.Select “Software Reset”. 6.Select “Auto Scan” or “Manual Selection”. 7.Select “Maybach”. 8.It prompts to switch on the ignition. After this, it prompts “Communicating, please wait…” In about 1s,it displays “Confirm total service”. 9.Select “Confirm total service”, it shows oil type (level). 10.Select any type (level), it will display “Oil reset completed”. Click OK to complete. More...

  After replacing new tire pressuring sensors or new tire pressure monitoring control module ,you need to perform programming.So here car-auto-repair.com show you guide on how to use  Launch X431 to program TPMS for FIAT Freemont 2014.For more Fiat repair,please check here:FIAT Trouble Repair What You Need? Launch X431 V+ Precautions To run this function correctly, ensure the following conditions: 1.The vehicle is equipped with tire pressure monitoring module and the module is in normal communication. The ignition key is in the ON position. All wires and connectors are properly tightened. The communication fault may occur in poor condition or low battery of the car. 2.The gear selector must be in P position. 3.The sensor ID on the label on the back of the sensor must be entered exactly. Operation Instructions Access the vehicle software via the X-431 Pro series diagnostic device, select the correct model,and then enter the special function of the tire pressu...

  Digiprog 3 v4.94  odometer correction tool how to use for Audi A8 (2003-). Here are notes for you all, of Tacho meter value Audi A8 (2003-) Diagnostic connection is located in the cabin Connect Diagnosis Port with DP3 cable of Plug 16 Ignition on Connect the DigiProg 3 main unit to Plug 16 The DigiProg needs no separate electricity supply; it is supplied via the diagnosis port Follow DigiProg3 v4.94 instruction and change KM Enter KM value and confirm Entry Audi A8 mileage correction completed! Before: After: Job’s done! Note: If error message “Access denied” pops up, pls. choose: PKW/LKW-Audi-A8-2003-(4E) 1. Flash Cxxx/ Dxxx Confirm with Hook Remove fuse 5 + 10 Wait approx. 5 seconds Reinstall fuse if tacho meter is dark Switch Ignition on and off Choose program: PKW/LKW– Audi—A8-2003-(4E) Diag Enter KM value and confirm Entry.

  Purpose: Change the mileage of a Smart Fortwo 2002 via an OBDII cable Car: Smart ForTwo CM01 – year 2002 Odometer correction tool: Digiprog 3 Chinese version Method: ODB2 Issues: Digiprog 3 says “NO CONNECTION”. Suggestion & Solutions: 2002 cannot be done via obd!! First you have to reset the bcu and then correct the milage in the dash (its a eeprom C66). Setting the eeprom worked fine. Note 1: Wrong Pinouts Sometimes Chinese cable schematics is wrong. Note 2: What is BCU? BCU= Bord Control Unit. is under the steering wheel on the left side. (inside the reilais box). you have to dismount it and connect like in the manual. until now i couldnt find the right pinout for the Digiprog(im seraching). For me it worked only with “Tacho Pro”. In the dash you can find two C66 eeproms you need the right one. You have to connect the red wire with the lower left leg of the eeprom (i couldnt connect it with the clip it worked only by soldering every single wire). ...